Alternative Front Brake Master Cylinder
-
- Avgas Sniffer
- Posts: 2120
- Joined: Sat Jun 09, 2007 10:10 am
- Location: Pig on the wall country
Alternative Front Brake Master Cylinder
Anyone using one off another bike ?
A radial one perhaps ?
A radial one perhaps ?
Can it yer old boiler
-
- Avgas Sniffer
- Posts: 3926
- Joined: Fri Jun 18, 2010 11:29 am
- Location: Oxfordshire
Re: Alternative Front Brake Master Cylinder
I'm using a ZX6 Nissin radial MC Martin if that helps, brakes feel amazing.
-
- Avgas Sniffer
- Posts: 2120
- Joined: Sat Jun 09, 2007 10:10 am
- Location: Pig on the wall country
Re: Alternative Front Brake Master Cylinder
Cheers Luders
Just can't get the feel of the standard one unless I have done something wrong, I have to use 4 fingers to pull up at any urgency
Only been on bike 7 years
I have been riding other bikes (Buell, Bonneville) and they have a better feel for sure
Just can't get the feel of the standard one unless I have done something wrong, I have to use 4 fingers to pull up at any urgency
Only been on bike 7 years
I have been riding other bikes (Buell, Bonneville) and they have a better feel for sure
Can it yer old boiler
-
- Avgas Sniffer
- Posts: 3926
- Joined: Fri Jun 18, 2010 11:29 am
- Location: Oxfordshire
Re: Alternative Front Brake Master Cylinder
yeah one of those should help a lot with feel. 2 finger braking is all you should need.
-
- Avgas Sniffer
- Posts: 3926
- Joined: Fri Jun 18, 2010 11:29 am
- Location: Oxfordshire
Re: Alternative Front Brake Master Cylinder
One second hand locally
http://www.ebay.co.uk/itm/322307915126
http://www.ebay.co.uk/itm/322307915126
-
- Avgas Sniffer
- Posts: 2120
- Joined: Sat Jun 09, 2007 10:10 am
- Location: Pig on the wall country
- JanBros
- Avgas Sniffer
- Posts: 3306
- Joined: Wed Jul 26, 2006 11:50 pm
- Location: the land of Francorchamps
Re: Alternative Front Brake Master Cylinder
something is definitly wrong, I never needed 4 fingers.headcoats wrote: Just can't get the feel of the standard one unless I have done something wrong, I have to use 4 fingers to pull up at any urgency
My ultimate goal is to die young as late as possible !
-
- Avgas Sniffer
- Posts: 2120
- Joined: Sat Jun 09, 2007 10:10 am
- Location: Pig on the wall country
Re: Alternative Front Brake Master Cylinder
This is what I thought
Brakes were all rebuilt with genuine seals and master cylinder , stainless pistons and braided lines
One thing was that they were a pig to bleed , just couldn't get the last bit of air out until I cable tied the front brake lever back overnight
Have noticed though if I haven't been on bike for a few weeks they feel spongy until I pump the lever
That's why I think the master cylinder is suspect
Always passed the MOT and I MOT mine at a brake specialist who test the brakes on their drum machine
Brakes were all rebuilt with genuine seals and master cylinder , stainless pistons and braided lines
One thing was that they were a pig to bleed , just couldn't get the last bit of air out until I cable tied the front brake lever back overnight
Have noticed though if I haven't been on bike for a few weeks they feel spongy until I pump the lever
That's why I think the master cylinder is suspect
Always passed the MOT and I MOT mine at a brake specialist who test the brakes on their drum machine
Can it yer old boiler
-
- Avgas Sniffer
- Posts: 3926
- Joined: Fri Jun 18, 2010 11:29 am
- Location: Oxfordshire
Re: Alternative Front Brake Master Cylinder
Sounds likely Martin
- JanBros
- Avgas Sniffer
- Posts: 3306
- Joined: Wed Jul 26, 2006 11:50 pm
- Location: the land of Francorchamps
Re: Alternative Front Brake Master Cylinder
still air in them.
My ultimate goal is to die young as late as possible !
-
- Heavy Smoker
- Posts: 158
- Joined: Mon Nov 20, 2006 9:23 pm
- Location: Cornwall
Re: Alternative Front Brake Master Cylinder
I've fitted a Brembo aftermarket radial master cylinder to my KR, works very nicely and is very well made.
Did you have two simple brake hoses fitted? this makes it a little easier bleeding than the original setup of 3 pipes with a splitter.
You could clean out the original master cylinder and fit a new seal kit and brake lever inc pivot bolt if you want to keep it original? They work reasonably well as standard if the bore isn't worn.
If the brake calipers have been cleaned out properly then the new pistons should slide back in the caliper freely and smoothly, try pushing them back to check? I prefer the genuine pistons, is there any difference to the problem if brakes are hot or cold?
Did you have two simple brake hoses fitted? this makes it a little easier bleeding than the original setup of 3 pipes with a splitter.
You could clean out the original master cylinder and fit a new seal kit and brake lever inc pivot bolt if you want to keep it original? They work reasonably well as standard if the bore isn't worn.
If the brake calipers have been cleaned out properly then the new pistons should slide back in the caliper freely and smoothly, try pushing them back to check? I prefer the genuine pistons, is there any difference to the problem if brakes are hot or cold?
Hardcore you know the score
-
- Heavy Smoker
- Posts: 420
- Joined: Fri Sep 19, 2014 6:44 pm
- Location: South Manchester
Re: Alternative Front Brake Master Cylinder
When you bleed the lines don't forget to bleed the top banjo bolt as well. Friend of mine spent 2 hours bleeding his brakes and got nowhere. 30 seconds after bleeding the top banjo bolt the lever pressure was perfect
-
- Avgas Sniffer
- Posts: 2120
- Joined: Sat Jun 09, 2007 10:10 am
- Location: Pig on the wall country
Re: Alternative Front Brake Master Cylinder
They do get better as they warm up
Can it yer old boiler
-
- Heavy Smoker
- Posts: 199
- Joined: Wed Dec 16, 2009 9:41 pm
- Location: Shetland
Re: Alternative Front Brake Master Cylinder
I had a hell of a time bleeding up freshly rebuilt calipers and master cylinder.
The over night cable tie helped, but what made the biggest difference was taking the bike out and generating a lot of heat using it a few times.
It went spongy when cold for a few rides, but ended up feeling very good indeed.
Oh and I got a zxr400 master cylinder, loads about as those pesky kids can't stay upright.
Cheers martin.
The over night cable tie helped, but what made the biggest difference was taking the bike out and generating a lot of heat using it a few times.
It went spongy when cold for a few rides, but ended up feeling very good indeed.
Oh and I got a zxr400 master cylinder, loads about as those pesky kids can't stay upright.
Cheers martin.