Yamasaki

Gordi · Post by **Gordi** » Sat Sep 04, 2010 8:52 pm

Thanks for that Scott. Will have a look in the morning. Do KR-1 owners have any hair???

Howie · Post by **Howie** » Sun Sep 05, 2010 5:18 pm

Do KR-1 owners have any hair???

Loads but it's not as black as it use to be

Gordi · Post by **Gordi** » Sat Sep 11, 2010 12:52 pm

Hi everyone, just passed MoT at last!!! Just want to thank Ray, Ben and Charles for all their help on this project. And thanks also to everyone else on this forum for their advice and encouragement. You know who you are. And a big thank you to Ali for running this site, couldn't have done it without you!
Cheers again!!

What now?

Charles · Post by **Charles** » Sat Sep 11, 2010 1:09 pm

Gordi wrote:What now?

Grow some hair

And post a clip of your bike on youtube.

Cheers,
Charles

Gordi · Post by **Gordi** » Sat Sep 11, 2010 1:17 pm

LOL!!
I'll try both, Charles. Which is easier??

ScottaKR · Post by **ScottaKR** » Sat Sep 11, 2010 1:29 pm

Glad to hear you got it sorted and on the road now Gordi. =D> =D>
What ended up being the problem with the brakes?
Can't wait to see a clip of it up on youtube.

And as for the hair issue, I keep mine nice and short so I cant get enough of a grip on it to tare it out. Mind you, the KR1 has been a dream compared to the old KR250. I swear that things what started sending me grey.

Cheers mate, and enjoy the ride.

Gordi · Post by **Gordi** » Sat Sep 11, 2010 1:44 pm

Cheers Scott. Finished up borrowing a calliper from Ray's TZR350 for MoT. Problem on my calliper can only be the dust seals on the pistons. I'll strip the calliper again tomorrow and reassemble it without them and see if that changes things. I'm pretty sure it can only be that which is stopping pistons going back when the brake is released. Bloody pattern parts!!

KwakOn · Post by **KwakOn** » Sat Sep 11, 2010 7:00 pm

this may have been suggested - are the inner seals, packers, slightly angled where they go against the piston. If they are then they must go in the right way round. lower edge towards disc if IRC.

Gordi · Post by **Gordi** » Sun Sep 12, 2010 6:11 am

Thanks for the hint, Kwakon, I'll have a look although these callipers have been apart loads of times now and I've not noticed any angles on the seals. The brakes are from a TZR so I think the next move is to (reluctantly) buy some genuine Yamaha seals.

Gordi · Post by **Gordi** » Tue Sep 14, 2010 9:05 pm

Can anyone foresee any problems running 155 main jets on the replacement Keihin 28 carbs with K & N filters? Will they be too big?

Luders · Post by **Luders** » Tue Sep 14, 2010 9:40 pm

Will be very rich on full throttle. Why 155's out of interest?

Gordi · Post by **Gordi** » Wed Sep 15, 2010 5:14 am

They're the only ones my mate had in his workshop. Don't know much about jetting myself but at the moment the bike is bogging down/won't rev freely on the 135. Just thought it needed bigger jets.

Charles · Post by **Charles** » Wed Sep 15, 2010 7:01 am

The 135s can't be right with those K&N filters, so if you haven't got any other jets atm than the 155s just try them.....

Charles

Luders · Post by **Luders** » Wed Sep 15, 2010 7:21 am

You'll probably need to do a full carb setup in that case.

Jets are not very expensive, I'll PM you the info.

Charles · Post by **Charles** » Wed Sep 15, 2010 7:27 am

Luders wrote:You'll probably need to do a full carb setup in that case.

True, setting up the main jet is only the start.

Charles

KR-1S.co.uk Forum

Yamasaki

!!

Thanks, guys

Re: Thanks, guys

!

Brakes

Seals

Main jets

Carbs