Plastic welding

Plastic bits and Paint
User avatar
tescr500
Oil Injector
Posts: 742
Joined: Sat Aug 29, 2009 12:05 pm
Location: hampshire

Post by tescr500 » Wed Sep 14, 2011 10:38 pm

i have a brken ear will have to be done but hopefully go ok fingers crossed and tab on rear unit
No Matter How Messy Things Get You Can Always Clean Them Up.
MY MAMMA TOLD ME, IF YOU AIN'T GOT ANY PROBLEMS DON'T MAKE ONE.
TIME IS PRECIOUS WASTE IT WISELY

User avatar
Howie
Avgas Sniffer
Posts: 2054
Joined: Mon Mar 16, 2009 9:33 pm
Location: East Yorkshire

Post by Howie » Thu Sep 15, 2011 10:18 am

Hey Howie, seeing as you are now our "Resident plastic welder" can I book my Rayban's in as I broke them in half on my hols
:lol: Sorry I've only just progressed to Oakleys.

This first pic shows a mend to the airbox from my Ke175, the hole was caused by the exhaust burning a hole in it (about the size of a 20p)

Image

This was done by bridging the hole using the plastic rod. Tack to one side then tack to the other. Once I had covered the hole with the rod, I melted them all together, not pretty but effective.

The next pic shows a repair to my Kx250's airbox

Image

Once again, not pretty :lol: This was just a split. The plastic on this part of the airbox is very thin, so I'm not going to dress this weld either.

Here's the ear

Image

This ear has fallen off once but now feels strong. Stronger than the fibre glass repair done by a previous owner. This will need grinding down & filling before repainting. Just need to find a good flexible filler now, any suggestions?

Finally here are some of the stuff you need.....

Image

I also have spring clips to hold things in place & a dremel type tool to grind back the excess weld.

User avatar
500bernie
Avgas Sniffer
Posts: 3325
Joined: Mon Aug 02, 2010 10:22 am
Location: Teesside

Post by 500bernie » Thu Sep 15, 2011 11:22 am

Well done Howie =D> =D> =D>

I feel inspired [-o<
Firecracker Red and Grey C3 300

User avatar
Howie
Avgas Sniffer
Posts: 2054
Joined: Mon Mar 16, 2009 9:33 pm
Location: East Yorkshire

Post by Howie » Thu Sep 15, 2011 9:26 pm

Best to just get stuck in Bernie.

I practised on a few old crappy fairings first, just to get a feel for it. Then thought 'bugger it' learn from your mistakes & all that.

Obviously I'm no expert regardless of what twostrokesmoker thinks :lol: but I think with more practice I could get a better finish.

I'm not sure what the technical term is but if you 'pool' the plastic (swirl it about with the soldering iron) you seem to get a better 'fix' to the original plastic.

I've got another weld to do on the Ke175's plastic. If I remember I'll do it stage by stage & post the pics on here.

User avatar
KR-1R
Premix Junkie
Posts: 1521
Joined: Wed May 16, 2007 2:24 am

Plastic welding with Hot Stapler

Post by KR-1R » Fri Apr 10, 2020 6:43 am

.
.
so a month or two back saw on aliexpress Hot Staplers
These have probably been in the bumper repair industry for years :| :oops:
but could increase crack repair strength without requiring full penetration hot air plastic welding skills

Image

A trimmable wire insert is halfway melted through/into the plastic thickness to lock together the halves of a crack.
The tails of the wire insert is trimmed back and filler applied

Image

Kits for not much more dollars than traditional solder iron

plenty example videos on youtube

https://youtu.be/1VN6lxdC9LY

https://youtu.be/ig9FAdMZ8Xk

the V shaped hot knife blade is then be used to melt ABS filler rod to fill the crevice left by the insert

Image

Frunobulax
Newbie
Posts: 24
Joined: Thu Nov 28, 2019 6:39 am

Re: Plastic welding

Post by Frunobulax » Sat Apr 11, 2020 7:18 am

Thanks for sharing, this looks very easy to use. I'll try this.

Post Reply