they have attachements for springs to fit them to the cylinders, not very good visible on the picture, but they are located where the paper hangs on the pipe.
KR-1R pipes
-
JanBros
- Avgas Sniffer
- Posts: 3319
- Joined: Wed Jul 26, 2006 11:50 pm
- Location: the land of Francorchamps
KR-1R pipes
are these what I believe/hope they are
they have attachements for springs to fit them to the cylinders, not very good visible on the picture, but they are located where the paper hangs on the pipe.
they have attachements for springs to fit them to the cylinders, not very good visible on the picture, but they are located where the paper hangs on the pipe.
My ultimate goal is to die young as late as possible !
-
Top-shaggy
- Premix Junkie
- Posts: 1966
- Joined: Mon Oct 31, 2011 11:09 pm
- Location: Derbyshire
-
KR-1R
- Premix Junkie
- Posts: 1588
- Joined: Wed May 16, 2007 2:24 am
.
.
no I think the may be TZR kit pipes, or gibsons (hydroformed)...
the connection at the head would be exterior o-rings
the straightness and header angle
and the rear frame tab is different
.
no I think the may be TZR kit pipes, or gibsons (hydroformed)...
the connection at the head would be exterior o-rings
the straightness and header angle
and the rear frame tab is different
Last edited by KR-1R on Fri Feb 01, 2013 1:57 am, edited 3 times in total.
-
JanBros
- Avgas Sniffer
- Posts: 3319
- Joined: Wed Jul 26, 2006 11:50 pm
- Location: the land of Francorchamps
funny story actualydave32 wrote: They up for sale somehwere Jan?
My ex-dealer (he quited the bike-buisness) bought over 10 years an almost complete KR1 in parts. the bike was at a point stolen, and was later found again, but the owner didn't want the hassle of putting it back together and just sold the parts.
over the years, I had bought the engine and all the parts you can brake while crashing
Some 6 years ago, he had enough of bikes and closed his shop, but still has about 120m² of used parts stored. But he is planning to get rid off them (as a joblot) , so I asked if I could quickly buy some parts I could use (I still have quite a good contact with him). So yesterday I was there, and as we were cruising between all the parts, I noticed these exhausts and thought "hmm, they look special and they look KR"
, and apparently it were the pipes that came with that KR1 (it was the only one he ever had for parts).I never bothered to ask/buy the pipes because somehow I automaticaly presumed they would be standard KR1, if only I knew
](./images/smilies/eusa_wall.gif "Brick wall"){kind=small}
but the good part of the story is, I now have them for free
the build quality is very high, beautiful welds that look like a robot did them. If these are welded by hand, the man that did them surely is a pro. general condition is very good, apart from some rust and 1 dent.
they definitly are KR1, I compared them to KR1S pipes, and the form and the position of the rear bracket matches . They are a lot shorter though, so probably good on higher rev's and less mid-range ... the way a proper 2-stroke is supposed to be
My ultimate goal is to die young as late as possible !
-
fred
- Oil Injector
- Posts: 926
- Joined: Sat Mar 22, 2008 5:42 pm
- Location: retford n,nott`s working in cotswolds
- Contact:
-
dave32
- Heavy Smoker
- Posts: 472
- Joined: Sun Oct 24, 2010 10:15 pm