BANG!

Twangled your powervalve grommit in your woodruff key? ask someone how to fix it here
User avatar
kwackman12
Oil Injector
Posts: 924
Joined: Wed Jul 04, 2007 10:06 pm
Location: Reading

BANG!

Post by kwackman12 »

Just got back from Snetterton all was going well untill the last session! smoke started pouring out of the right hand exhaust, but no rattles or knocks & engine still runs fine?? what do you think crankshaft oil seal?
I feel I must comment on the pfm/fireblade front brake set up though! bloody awsome!! def recommend these, one finger braking & powerfull enough to launch you over the front! "& no i didn't" :mrgreen:
KR1 race bike
ZXR 400 Race Bike
Aprilia RS250
Charles
Premix Junkie
Posts: 1804
Joined: Tue Jun 26, 2007 3:59 pm
Location: Fourques, France

Post by Charles »

I'd guess the oil seal :cry:
User avatar
kwackman12
Oil Injector
Posts: 924
Joined: Wed Jul 04, 2007 10:06 pm
Location: Reading

Post by kwackman12 »

"Bugger" thats what i was thinking Charles, better get the spanners out as i have another trackday booked at Oulton park on the 1st July ](*,)
KR1 race bike
ZXR 400 Race Bike
Aprilia RS250
User avatar
mr_bungholeo
Premix Junkie
Posts: 1225
Joined: Wed Mar 21, 2007 7:55 pm
Location: braintree

Post by mr_bungholeo »

check the coolant too..it may be the head gasket as they seem to fail quickly...but seals slowly get worse..... :D
bring a ding ding i'm a throttle happy chappy...:)

you cant beat a bit of blue haze...
danny harris.....R.I.P
gone but totally forgotten...:)
wakasaki
Heavy Smoker
Posts: 437
Joined: Tue Oct 02, 2007 10:28 am

Post by wakasaki »

As said...
if the gearbox oil has gone down yep...

And if it is the main oil seal right crankside
Its a rebuild ..because the primary drive gear
is pressed heated...
and they normally weld them after a rebuild / after balancing..

ooohhhhhhhhhhhh.......
Still worse things happen...

G
User avatar
kwackman12
Oil Injector
Posts: 924
Joined: Wed Jul 04, 2007 10:06 pm
Location: Reading

Post by kwackman12 »

Just taken the barrels off, no sign of head gasket leak, coolant loss or geabox oil loss! but i have found different size oil feed pipes going to the inlet rubbers, right side crancase has an excessive amount of (red) two stroke oil sitting in it, one of the oil check valves also seems to be missing the right side where the smoke is!
So just ordered new rings,base gaskets,little ends & carb mounting rubbers. But i need a new set of oil feed pipes complete with all the fittings (not available from mr K anymore) does anyone have a set please!!! [-o< happy to pay for them. Hopefully this is the problem
KR1 race bike
ZXR 400 Race Bike
Aprilia RS250
Charles
Premix Junkie
Posts: 1804
Joined: Tue Jun 26, 2007 3:59 pm
Location: Fourques, France

Post by Charles »

kwackman12 wrote: But i need a new set of oil feed pipes complete with all the fittings (not available from mr K anymore) does anyone have a set please!!! [-o< happy to pay for them.
I have a spare set you could have, but probably so does one of the UK-gentlemen :D
User avatar
mr_bungholeo
Premix Junkie
Posts: 1225
Joined: Wed Mar 21, 2007 7:55 pm
Location: braintree

Post by mr_bungholeo »

im sure i can find a spare set or two in the pile...... :wink:
bring a ding ding i'm a throttle happy chappy...:)

you cant beat a bit of blue haze...
danny harris.....R.I.P
gone but totally forgotten...:)
Charles
Premix Junkie
Posts: 1804
Joined: Tue Jun 26, 2007 3:59 pm
Location: Fourques, France

Post by Charles »

mr_bungholeo wrote:im sure i can find a spare set or two in the pile...... :wink:
that's what I thought :D
User avatar
kwackman12
Oil Injector
Posts: 924
Joined: Wed Jul 04, 2007 10:06 pm
Location: Reading

Post by kwackman12 »

Thanks for that chaps, has anyone come across this before?
KR1 race bike
ZXR 400 Race Bike
Aprilia RS250
User avatar
nate
Heavy Smoker
Posts: 437
Joined: Wed Jan 10, 2007 4:57 pm
Location: Cornwall

Post by nate »

no.... both my oil feed tubes are the same size on both my engines

Glad I checked though :mrgreen:
falconman
Heavy Smoker
Posts: 225
Joined: Sun Jul 22, 2007 9:23 am
Location: West Coast, USA

Post by falconman »

I would check the crankcase to see if the check valve is still in there. Hate to see the motor go boom again after all the work.
Cliff
Premix Junkie
Posts: 1264
Joined: Tue Jul 25, 2006 6:35 pm
Location: Lincolnshire

Post by Cliff »

I have come across a blocked check valve before, it was after a bike had been laid up in a damp garage for a couple of years. Freed it with a pin and WD 40.
Possible yours had been blocked at some time, and some "mechanic" has fixed it by cutting it off.
User avatar
kwackman12
Oil Injector
Posts: 924
Joined: Wed Jul 04, 2007 10:06 pm
Location: Reading

Post by kwackman12 »

Cliff did it give the same symptoms as i had, excessive smoke?
I have come across a blocked check valve before, it was after a bike had been laid up in a damp garage for a couple of years. Freed it with a pin and WD 40.
Possible yours had been blocked at some time, and some "mechanic" has fixed it by cutting it off.
KR1 race bike
ZXR 400 Race Bike
Aprilia RS250
Cliff
Premix Junkie
Posts: 1264
Joined: Tue Jul 25, 2006 6:35 pm
Location: Lincolnshire

Post by Cliff »

The side that was blocked never smoked at all, thats why i looked into it and read about the check valve. I reckon that they must hold back the flow of oil slightly as the pressure has to pass through a ball/spring thingy.
If one of your valves are missing, i would think it will allow more oil to travel down that tube , thus more smoke. Hopefully that will be it.
Post Reply